Вернуться в категорию

ПА6 Ударопрочный

ПА / Нейлон

Ударопрочный PA6 B2XLZ0 с ударной вязкостью 100 кДж/м² и удлинением 350% для многослойной соэкструзии и выдувной тары для продуктов и лекарств. Запросите TDS, образцы и цену.

Бесплатные образцы: 5–10 кг. Пробный заказ: от 25 кг. Серийное производство: от 1 000 кг. Доставку оплачивает заказчик.

Jinsu ещё не завершила сертификацию UL Yellow Card. Данные TDS и результаты испытаний UL94 не означают признания UL. Если проект требует Yellow Card, проверьте сертификацию конкретной марки перед одобрением или закупкой.

Технические Характеристики

  • •B2XLZ0 · Ударопрочный PA6
  • •100 kJ/m² ударная вязкость с надрезом · ISO 179
  • •Удлинение 350% · Многослойная соэкструзия и выдув

Применение

Многослойная соэкструзионная упаковкаВыдувная тара для пищевых продуктовВыдувная тара для лекарствЭкструзионная пленка и листГорячий розлив и холодовая цепь

Технический паспорт (TDS) · PA6 B2XLZ0

СвойствоМетод испытанияУсловия испытанияТипичное Значение
ПлотностьISO 118323°C1.08 g/cm3
Прочность на РастяжениеISO 52750 mm/min30 MPa
Удлинение при РазрывеISO 52750 mm/min350%
Прочность на ИзгибISO 1782 mm/min25 MPa
Модуль УпругостиISO 1782 mm/min600 MPa
Ударная вязкость по Шарпи с надрезомISO 17923°C100 kJ/m2
Температура Деформации (HDT) · 0,45 МПаISO 75без отжига105°C
Класс ОгнестойкостиUL 941.6 / 2.0 / 3.2 mmHB

Типичные значения и диапазоны характеристик служат для выбора марки. Рецептуры можно адаптировать к требованиям применения. Итоговые характеристики определяются TDS выбранной марки; эти значения не являются гарантированными спецификациями.

  • Таблица относится только к B2XLZ0. Для других марок используйте отдельный TDS.
  • Типичные значения из паспортов указанных марок служат для выбора и не являются универсальными свойствами или гарантией поставки. Уточните цвет, образец и условия испытаний предлагаемой марки.

Условия Переработки · B2XLZ0

Температура Сушки

80–90°C

Время Сушки

2–4 h

Температура расплава

220–230°C

Температура Пресс-формы

80–100°C

Хранение и Обращение

ПА6 чрезвычайно гигроскопичен. Хранить герметично в сухой среде. Использовать в течение 24 часов после вскрытия или повторно высушить.

Suzhou Jinsu New Material Co., Ltd.

WhatsApp: +86 17351132569

sales@maxnmtech.com

Подробное применение

Многослойная соэкструзионная упаковка

B2XLZ0 is typically run in a five-layer structure such as PE structural layer / tie layer / toughened PA6 / tie layer / PE sealing layer. The toughened layer delivers barrier and impact resistance, the PE layers handle heat sealing and cost, and the tie layers bond nylon to polyolefin. Hold melt temperature at 220–230°C and keep inter-layer temperature differences under 30°C, or the parison develops interface instability and delamination.

Выдувная тара для пищевых продуктов и лекарств

Melt strength decides the blow-molding window: B2XLZ0 runs at about 2 g/10min MFI (235°C/2.16kg), so sag is low and large-diameter, high-neck-ratio bottles and jerry cans are practical. Mold temperature of 80–100°C improves surface gloss and dimensional stability; vent the mold properly or the inner wall develops pitting. For food contact, specify food-grade colorants and additives and supply compliance statements under the target market's rules, such as EU 10/2011 or FDA 21 CFR.

Экструзионная пленка, лист и горячий розлив

Beyond hollow blow molding, B2XLZ0 also suits cast film, thermoforming sheet and hot-fill packaging. HDT is 105°C at 0.45 MPa, so 85–95°C hot fill and pasteurisation cycles are tolerable; on the cold side the 350% elongation keeps containers from cracking in frozen storage and cold-chain transport. Dry to below 0.1% moisture before extrusion or the film shows bubbles and silver streaks.

Часто задаваемые вопросы

Можно ли применять ударопрочный PA6 в контакте с пищей?

Yes, with a food-grade formulation. B2XLZ0 natural base resin carries no restricted additives, but confirm the colorant, antioxidant and release agent are food-grade for the actual shipment, and supply compliance statements for the target market (EU 10/2011, FDA 21 CFR, and so on). Pharmaceutical packaging also needs extractables and leachables assessment.

На что обращать внимание при многослойном соэкструзионном выдуве?

Three things matter most: interlayer adhesion, which needs a matched tie-layer resin or the container delaminates on impact; closely matched melt temperatures across layers, held within 30°C to avoid interface disturbance; and drying, with PA6 moisture below 0.1% or bubbles and silver streaks appear. Use an adjustable die to fine-tune parison wall distribution.

Чем B2XLZ0 отличается от стандартного PA6?

Standard PA6 is stronger and stiffer but elongates only tens of percent and cracks easily under low-temperature or high-rate impact. B2XLZ0 trades some stiffness and strength (600 MPa modulus, 30 MPa tensile) for 100 kJ/m² notched impact and 350% elongation, which suits packaging and containers that must absorb impact energy.