PA6 Renforcé Choc
PA / Nylon
PA6 résilient B2XLZ0 avec choc entaillé de 100 kJ/m² et allongement de 350%, pour coextrusion multicouche et contenants alimentaires et pharmaceutiques soufflés. Demandez la TDS, des échantillons et un devis.
Échantillons gratuits : 5–10 kg. Commandes d’essai : minimum 25 kg. Production régulière : minimum 1 000 kg. Le transport est à la charge du client.
Jinsu n’a pas encore obtenu la certification UL Yellow Card. Les données TDS et les résultats d’essais UL94 ne constituent pas une reconnaissance UL. Si votre projet exige une Yellow Card, vérifiez la certification du grade exact avant validation ou achat.
Spécifications Techniques
- •B2XLZ0 · PA6 résilient
- •100 kJ/m² choc entaillé · ISO 179
- •Allongement 350% · Coextrusion multicouche et soufflage
Applications
Fiche Technique (TDS) · PA6 B2XLZ0
| Propriété | Méthode d’essai | Conditions d’essai | Valeur Typique |
|---|---|---|---|
| Masse Volumique | ISO 1183 | 23°C | 1.08 g/cm3 |
| Résistance à la Traction | ISO 527 | 50 mm/min | 30 MPa |
| Allongement à la Rupture | ISO 527 | 50 mm/min | 350% |
| Résistance à la Flexion | ISO 178 | 2 mm/min | 25 MPa |
| Module de Flexion | ISO 178 | 2 mm/min | 600 MPa |
| Résistance au choc Charpy entaillé | ISO 179 | 23°C | 100 kJ/m2 |
| Température de Déformation (HDT) · 0,45 MPa | ISO 75 | non recuit | 105°C |
| Classement au Feu | UL 94 | 1.6 / 2.0 / 3.2 mm | HB |
Les valeurs typiques et plages de performances servent au choix du grade. Les formulations sur mesure peuvent être adaptées aux exigences de l’application. Les propriétés finales sont définies dans le TDS du grade choisi et ne constituent pas des garanties de spécification.
- Ce tableau concerne uniquement B2XLZ0. Consultez la TDS propre à tout autre grade.
- Les valeurs typiques des fiches des grades cités servent à la sélection ; elles ne constituent ni des propriétés universelles ni des garanties de fourniture. Confirmez couleur, éprouvette et conditions d’essai du grade proposé.
Conditions de Mise en Œuvre · B2XLZ0
80–90°C
2–4 h
220–230°C
80–100°C
Stockage & Manutention
Le PA6 est très hygroscopique. Stocker hermétiquement dans un environnement sec. Utiliser dans les 24 heures après ouverture ou sécher à nouveau.
Produits Associés
Suzhou Jinsu New Material Co., Ltd.
WhatsApp: +86 17351132569
sales@maxnmtech.com
Applications détaillées
Emballage en coextrusion multicouche
B2XLZ0 is typically run in a five-layer structure such as PE structural layer / tie layer / toughened PA6 / tie layer / PE sealing layer. The toughened layer delivers barrier and impact resistance, the PE layers handle heat sealing and cost, and the tie layers bond nylon to polyolefin. Hold melt temperature at 220–230°C and keep inter-layer temperature differences under 30°C, or the parison develops interface instability and delamination.
Contenants alimentaires et pharmaceutiques soufflés
Melt strength decides the blow-molding window: B2XLZ0 runs at about 2 g/10min MFI (235°C/2.16kg), so sag is low and large-diameter, high-neck-ratio bottles and jerry cans are practical. Mold temperature of 80–100°C improves surface gloss and dimensional stability; vent the mold properly or the inner wall develops pitting. For food contact, specify food-grade colorants and additives and supply compliance statements under the target market's rules, such as EU 10/2011 or FDA 21 CFR.
Film, feuille extrudée et remplissage à chaud
Beyond hollow blow molding, B2XLZ0 also suits cast film, thermoforming sheet and hot-fill packaging. HDT is 105°C at 0.45 MPa, so 85–95°C hot fill and pasteurisation cycles are tolerable; on the cold side the 350% elongation keeps containers from cracking in frozen storage and cold-chain transport. Dry to below 0.1% moisture before extrusion or the film shows bubbles and silver streaks.
Questions fréquentes
Le PA6 résilient peut-il être utilisé au contact alimentaire ?
Yes, with a food-grade formulation. B2XLZ0 natural base resin carries no restricted additives, but confirm the colorant, antioxidant and release agent are food-grade for the actual shipment, and supply compliance statements for the target market (EU 10/2011, FDA 21 CFR, and so on). Pharmaceutical packaging also needs extractables and leachables assessment.
Que faut-il surveiller en extrusion-soufflage multicouche ?
Three things matter most: interlayer adhesion, which needs a matched tie-layer resin or the container delaminates on impact; closely matched melt temperatures across layers, held within 30°C to avoid interface disturbance; and drying, with PA6 moisture below 0.1% or bubbles and silver streaks appear. Use an adjustable die to fine-tune parison wall distribution.
En quoi B2XLZ0 diffère-t-il du PA6 standard ?
Standard PA6 is stronger and stiffer but elongates only tens of percent and cracks easily under low-temperature or high-rate impact. B2XLZ0 trades some stiffness and strength (600 MPa modulus, 30 MPa tensile) for 100 kJ/m² notched impact and 350% elongation, which suits packaging and containers that must absorb impact energy.