PA6 Tenacificado
PA / Nylon
PA6 tenacificado B2XLZ0 com impacto entalhado de 100 kJ/m² e alongamento de 350%, para coextrusão multicamada e recipientes alimentícios e farmacêuticos soprados. Solicite TDS, amostras e cotação.
Amostras grátis: 5–10 kg. Pedidos de teste: mínimo de 25 kg. Produção regular: mínimo de 1.000 kg. O cliente paga o frete.
A Jinsu ainda não concluiu a certificação UL Yellow Card. Dados TDS e resultados de ensaios UL94 não constituem reconhecimento UL. Se o projeto exigir uma Yellow Card, verifique a certificação do grau exato antes da aprovação ou compra.
Especificações Técnicas
- •B2XLZ0 · PA6 tenacificado
- •100 kJ/m² impacto entalhado · ISO 179
- •Alongamento 350% · Coextrusão multicamada e sopro
Aplicações
Ficha Técnica (TDS) · PA6 B2XLZ0
| Propriedade | Método de ensaio | Condições de ensaio | Valor Típico |
|---|---|---|---|
| Densidade | ISO 1183 | 23°C | 1.08 g/cm3 |
| Resistência à Tração | ISO 527 | 50 mm/min | 30 MPa |
| Alongamento na Ruptura | ISO 527 | 50 mm/min | 350% |
| Resistência à Flexão | ISO 178 | 2 mm/min | 25 MPa |
| Módulo de Flexão | ISO 178 | 2 mm/min | 600 MPa |
| Resistência ao impacto Charpy com entalhe | ISO 179 | 23°C | 100 kJ/m2 |
| Temperatura de Deflexão Térmica (HDT) · 0.45 MPa | ISO 75 | não recozido | 105°C |
| Classificação de Chama | UL 94 | 1.6 / 2.0 / 3.2 mm | HB |
Valores típicos e faixas de desempenho servem para a seleção da grade. Formulações personalizadas podem ser ajustadas aos requisitos da aplicação. As propriedades finais seguem o TDS da grade escolhida e não constituem garantias de especificação.
- Esta tabela se aplica apenas a B2XLZ0. Consulte a TDS específica dos outros grades.
- Os valores típicos das fichas dos grades indicados são referências de seleção, não propriedades universais nem garantias de fornecimento. Confirme cor, corpo de prova e condições de ensaio do grade ofertado.
Condições de Processamento · B2XLZ0
80–90°C
2–4 h
220–230°C
80–100°C
Armazenamento & Manuseio
PA6 é altamente higroscópico. Armazenar selado em ambiente seco. Usar em até 24 horas após abertura ou secar novamente.
Produtos Relacionados
Suzhou Jinsu New Material Co., Ltd.
WhatsApp: +86 17351132569
sales@maxnmtech.com
Aplicações detalhadas
Embalagem em coextrusão multicamada
B2XLZ0 is typically run in a five-layer structure such as PE structural layer / tie layer / toughened PA6 / tie layer / PE sealing layer. The toughened layer delivers barrier and impact resistance, the PE layers handle heat sealing and cost, and the tie layers bond nylon to polyolefin. Hold melt temperature at 220–230°C and keep inter-layer temperature differences under 30°C, or the parison develops interface instability and delamination.
Recipientes alimentícios e farmacêuticos soprados
Melt strength decides the blow-molding window: B2XLZ0 runs at about 2 g/10min MFI (235°C/2.16kg), so sag is low and large-diameter, high-neck-ratio bottles and jerry cans are practical. Mold temperature of 80–100°C improves surface gloss and dimensional stability; vent the mold properly or the inner wall develops pitting. For food contact, specify food-grade colorants and additives and supply compliance statements under the target market's rules, such as EU 10/2011 or FDA 21 CFR.
Filme, chapa extrudada e enchimento a quente
Beyond hollow blow molding, B2XLZ0 also suits cast film, thermoforming sheet and hot-fill packaging. HDT is 105°C at 0.45 MPa, so 85–95°C hot fill and pasteurisation cycles are tolerable; on the cold side the 350% elongation keeps containers from cracking in frozen storage and cold-chain transport. Dry to below 0.1% moisture before extrusion or the film shows bubbles and silver streaks.
Perguntas frequentes
O PA6 tenacificado pode ser usado em contato com alimentos?
Yes, with a food-grade formulation. B2XLZ0 natural base resin carries no restricted additives, but confirm the colorant, antioxidant and release agent are food-grade for the actual shipment, and supply compliance statements for the target market (EU 10/2011, FDA 21 CFR, and so on). Pharmaceutical packaging also needs extractables and leachables assessment.
O que observar na extrusão-sopro multicamada?
Three things matter most: interlayer adhesion, which needs a matched tie-layer resin or the container delaminates on impact; closely matched melt temperatures across layers, held within 30°C to avoid interface disturbance; and drying, with PA6 moisture below 0.1% or bubbles and silver streaks appear. Use an adjustable die to fine-tune parison wall distribution.
Como o B2XLZ0 difere do PA6 padrão?
Standard PA6 is stronger and stiffer but elongates only tens of percent and cracks easily under low-temperature or high-rate impact. B2XLZ0 trades some stiffness and strength (600 MPa modulus, 30 MPa tensile) for 100 kJ/m² notched impact and 350% elongation, which suits packaging and containers that must absorb impact energy.