العودة للفئة

PA6 مقاوم للصدمات

PA / نايلون

PA6 معدل للصدم B2XLZ0 بصدمة بحز 100 kJ/m² واستطالة 350%، للتشارك بالبثق متعدد الطبقات وعبوات الغذاء والدواء بالنفخ. اطلب TDS وعينات وسعرًا.

عينات مجانية: 5–10 كغ. الحد الأدنى للطلب التجريبي: 25 كغ. الحد الأدنى للإنتاج المعتاد: 1,000 كغ. يتحمل العميل تكاليف الشحن.

لم تُكمل Jinsu بعد شهادة UL Yellow Card. بيانات TDS ونتائج اختبارات UL94 لا تعني اعتماد UL. إذا كان مشروعك يتطلب البطاقة الصفراء، فتحقق من شهادة الدرجة المحددة قبل الموافقة أو الشراء.

المواصفات التقنية

  • •B2XLZ0 · PA6 معدل للصدم
  • •100 kJ/m² صدمة بحز · ISO 179
  • •استطالة 350% · بثق مشترك متعدد الطبقات ونفخ

التطبيقات

تعبئة بتشارك بثق متعدد الطبقاتعبوات غذائية بالنفخعبوات دوائية بالنفخأفلام وألواح بالبثقتعبئة ساخنة وسلسلة التبريد

ورقة البيانات الفنية (TDS) · PA6 B2XLZ0

الخاصيةطريقة الاختبارظروف الاختبارالقيمة النموذجية
الكثافةISO 118323°C1.08 g/cm3
قوة الشدISO 52750 mm/min30 MPa
استطالة عند الكسرISO 52750 mm/min350%
مقاومة الانحناءISO 1782 mm/min25 MPa
معامل الانحناءISO 1782 mm/min600 MPa
مقاومة الصدمات شاربي بالحزISO 17923°C100 kJ/m2
درجة حرارة الانحراف الحراري (HDT) · 0.45 MPaISO 75غير مُلدَّن105°C
تصنيف اللهبUL 941.6 / 2.0 / 3.2 mmHB

القيم النموذجية ونطاقات الأداء مخصصة لاختيار الدرجة. يمكن تعديل التركيبات المخصصة وفقًا لمتطلبات التطبيق. تُحدد الخصائص النهائية في TDS للدرجة المختارة ولا تمثل هذه القيم ضمانًا للمواصفات.

  • ينطبق هذا الجدول على B2XLZ0 فقط. راجع TDS المنفصل لأي درجة أخرى.
  • القيم النموذجية من أوراق الدرجات المذكورة هي مراجع للاختيار، وليست خصائص مادة عامة أو ضمانات شراء. تحقق من اللون والعينة وظروف الاختبار للدرجة المعروضة.

شروط المعالجة · B2XLZ0

درجة حرارة التجفيف

80–90°C

وقت التجفيف

2–4 h

درجة حرارة المصهور

220–230°C

درجة حرارة القالب

80–100°C

التخزين والمناولة

PA6 شديد الامتصاص للرطوبة. يُخزن محكم الإغلاق في بيئة جافة. يُستخدم خلال 24 ساعة بعد الفتح أو يُعاد تجفيفه.

Suzhou Jinsu New Material Co., Ltd.

WhatsApp: +86 17351132569

sales@maxnmtech.com

التطبيقات التفصيلية

التعبئة بتشارك البثق متعدد الطبقات

B2XLZ0 is typically run in a five-layer structure such as PE structural layer / tie layer / toughened PA6 / tie layer / PE sealing layer. The toughened layer delivers barrier and impact resistance, the PE layers handle heat sealing and cost, and the tie layers bond nylon to polyolefin. Hold melt temperature at 220–230°C and keep inter-layer temperature differences under 30°C, or the parison develops interface instability and delamination.

عبوات غذائية ودوائية بالنفخ

Melt strength decides the blow-molding window: B2XLZ0 runs at about 2 g/10min MFI (235°C/2.16kg), so sag is low and large-diameter, high-neck-ratio bottles and jerry cans are practical. Mold temperature of 80–100°C improves surface gloss and dimensional stability; vent the mold properly or the inner wall develops pitting. For food contact, specify food-grade colorants and additives and supply compliance statements under the target market's rules, such as EU 10/2011 or FDA 21 CFR.

الأفلام والألواح بالبثق والتعبئة الساخنة

Beyond hollow blow molding, B2XLZ0 also suits cast film, thermoforming sheet and hot-fill packaging. HDT is 105°C at 0.45 MPa, so 85–95°C hot fill and pasteurisation cycles are tolerable; on the cold side the 350% elongation keeps containers from cracking in frozen storage and cold-chain transport. Dry to below 0.1% moisture before extrusion or the film shows bubbles and silver streaks.

الأسئلة الشائعة

هل يمكن استخدام PA6 المقوى للتلامس مع الطعام؟

Yes, with a food-grade formulation. B2XLZ0 natural base resin carries no restricted additives, but confirm the colorant, antioxidant and release agent are food-grade for the actual shipment, and supply compliance statements for the target market (EU 10/2011, FDA 21 CFR, and so on). Pharmaceutical packaging also needs extractables and leachables assessment.

ما الذي يجب مراعاته في النفخ بتشارك البثق متعدد الطبقات؟

Three things matter most: interlayer adhesion, which needs a matched tie-layer resin or the container delaminates on impact; closely matched melt temperatures across layers, held within 30°C to avoid interface disturbance; and drying, with PA6 moisture below 0.1% or bubbles and silver streaks appear. Use an adjustable die to fine-tune parison wall distribution.

ما الفرق بين B2XLZ0 و PA6 القياسي؟

Standard PA6 is stronger and stiffer but elongates only tens of percent and cracks easily under low-temperature or high-rate impact. B2XLZ0 trades some stiffness and strength (600 MPa modulus, 30 MPa tensile) for 100 kJ/m² notched impact and 350% elongation, which suits packaging and containers that must absorb impact energy.