PA6 ทนแรงกระแทก
PA / ไนลอน
??? PA6 ???????????? B2XLZ0 ???????????????????? 100 kJ/m² ???????????? 350% ???????????????????????????????????????? ?????????????????????????? ?? TDS ?????????????????????
ตัวอย่างฟรี 5–10 กก. คำสั่งซื้อทดลองขั้นต่ำ 25 กก. การผลิตปกติขั้นต่ำ 1,000 กก. ลูกค้าเป็นผู้รับผิดชอบค่าขนส่ง
Jinsu ยังไม่ได้รับการรับรอง UL Yellow Card ข้อมูล TDS และผลทดสอบ UL94 ไม่ใช่การรับรองจาก UL หากโครงการต้องใช้ Yellow Card โปรดตรวจสอบการรับรองของเกรดนั้นก่อนอนุมัติหรือสั่งซื้อ
ข้อมูลจำเพาะทางเทคนิค
- •B2XLZ0 · PA6 เพิ่มความเหนียว
- •100 kJ/m² การกระแทกแบบมีรอยบาก · ISO 179
- •การยืดตัว 350% · ร่วมอัดรีดหลายชั้นและขึ้นรูปแบบเป่า
การใช้งาน
เอกสารข้อมูลทางเทคนิค (TDS) · PA6 B2XLZ0
| คุณสมบัติ | วิธีทดสอบ | เงื่อนไขการทดสอบ | ค่าทั่วไป |
|---|---|---|---|
| ความหนาแน่น | ISO 1183 | 23°C | 1.08 g/cm3 |
| ความต้านทานแรงดึง | ISO 527 | 50 mm/min | 30 MPa |
| ความยืดตัวเมื่อขาด | ISO 527 | 50 mm/min | 350% |
| ความต้านทานการดัด | ISO 178 | 2 mm/min | 25 MPa |
| มอดุลัสการดัด | ISO 178 | 2 mm/min | 600 MPa |
| ความแข็งแรงต่อการกระแทกแบบชาร์ปีมีรอยบาก | ISO 179 | 23°C | 100 kJ/m2 |
| อุณหภูมิโก่งตัวจากความร้อน (HDT) · 0.45 MPa | ISO 75 | ไม่ผ่านการอบอ่อน | 105°C |
| ระดับการหน่วงไฟ | UL 94 | 1.6 / 2.0 / 3.2 mm | HB |
ค่าทั่วไปและช่วงสมบัติใช้เป็นข้อมูลอ้างอิงในการเลือกเกรด สามารถปรับสูตรเฉพาะตามข้อกำหนดการใช้งานได้ สมบัติสุดท้ายอ้างอิง TDS ของเกรดที่เลือกและไม่ถือเป็นการรับประกันข้อกำหนด
- ตารางนี้ใช้กับ B2XLZ0 เท่านั้น สำหรับเกรดอื่นโปรดดู TDS ของเกรดนั้น
- ค่าทั่วไปจากเอกสารข้อมูลของเกรดที่ระบุใช้เพื่อการเลือกวัสดุ ไม่ใช่สมบัติทั่วไปหรือการรับประกันการจัดซื้อ โปรดยืนยันสี ชิ้นทดสอบ และเงื่อนไขการทดสอบของเกรดที่เสนอขาย
เงื่อนไขการขึ้นรูป · B2XLZ0
80–90°C
2–4 h
220–230°C
80–100°C
การจัดเก็บและการจัดการ
PA6 มีคุณสมบัติดูดความชื้นได้สูงมาก ควรเก็บไว้ในภาชนะที่ปิดสนิทในสภาพแวดล้อมที่แห้ง ใช้งานภายใน 24 ชั่วโมงหลังจากเปิดบรรจุภัณฑ์ หรือทำการอบแห้งใหม่
ผลิตภัณฑ์ที่เกี่ยวข้อง
Suzhou Jinsu New Material Co., Ltd.
WhatsApp: +86 17351132569
sales@maxnmtech.com
การประยุกต์ใช้งานโดยละเอียด
บรรจุภัณฑ์ร่วมอัดรีดหลายชั้น
B2XLZ0 is typically run in a five-layer structure such as PE structural layer / tie layer / toughened PA6 / tie layer / PE sealing layer. The toughened layer delivers barrier and impact resistance, the PE layers handle heat sealing and cost, and the tie layers bond nylon to polyolefin. Hold melt temperature at 220–230°C and keep inter-layer temperature differences under 30°C, or the parison develops interface instability and delamination.
บรรจุภัณฑ์อาหารและยาขึ้นรูปแบบเป่า
Melt strength decides the blow-molding window: B2XLZ0 runs at about 2 g/10min MFI (235°C/2.16kg), so sag is low and large-diameter, high-neck-ratio bottles and jerry cans are practical. Mold temperature of 80–100°C improves surface gloss and dimensional stability; vent the mold properly or the inner wall develops pitting. For food contact, specify food-grade colorants and additives and supply compliance statements under the target market's rules, such as EU 10/2011 or FDA 21 CFR.
ฟิล์ม แผ่นอัดรีด และบรรจุร้อน
Beyond hollow blow molding, B2XLZ0 also suits cast film, thermoforming sheet and hot-fill packaging. HDT is 105°C at 0.45 MPa, so 85–95°C hot fill and pasteurisation cycles are tolerable; on the cold side the 350% elongation keeps containers from cracking in frozen storage and cold-chain transport. Dry to below 0.1% moisture before extrusion or the film shows bubbles and silver streaks.
คำถามที่พบบ่อย
PA6 เพิ่มความเหนียวใช้สัมผัสอาหารได้หรือไม่
Yes, with a food-grade formulation. B2XLZ0 natural base resin carries no restricted additives, but confirm the colorant, antioxidant and release agent are food-grade for the actual shipment, and supply compliance statements for the target market (EU 10/2011, FDA 21 CFR, and so on). Pharmaceutical packaging also needs extractables and leachables assessment.
การขึ้นรูปแบบเป่าร่วมอัดรีดหลายชั้นต้องระวังอะไร
Three things matter most: interlayer adhesion, which needs a matched tie-layer resin or the container delaminates on impact; closely matched melt temperatures across layers, held within 30°C to avoid interface disturbance; and drying, with PA6 moisture below 0.1% or bubbles and silver streaks appear. Use an adjustable die to fine-tune parison wall distribution.
B2XLZ0 ต่างจาก PA6 มาตรฐานอย่างไร
Standard PA6 is stronger and stiffer but elongates only tens of percent and cracks easily under low-temperature or high-rate impact. B2XLZ0 trades some stiffness and strength (600 MPa modulus, 30 MPa tensile) for 100 kJ/m² notched impact and 350% elongation, which suits packaging and containers that must absorb impact energy.