PA6 ad alta tenacità
PA / Nylon
PA6 tenacizzato B2XLZ0 con impatto intagliato 100 kJ/m² e allungamento 350%, per coestrusione multistrato e contenitori alimentari e farmaceutici soffiati. Richiedi TDS, campioni e preventivo.
Campioni gratuiti: 5–10 kg. Ordini di prova: minimo 25 kg. Produzione regolare: minimo 1.000 kg. Le spese di spedizione sono a carico del cliente.
Jinsu non ha completato la certificazione UL Yellow Card. I dati TDS e i risultati delle prove UL94 non costituiscono un riconoscimento UL. Se il progetto richiede una Yellow Card, verifica la certificazione del grado specifico prima dell’approvazione o dell’acquisto.
Specifiche tecniche
- •B2XLZ0 · PA6 tenacizzato
- •100 kJ/m² impatto intagliato · ISO 179
- •Allungamento 350% · Coestrusione multistrato e soffiaggio
Applicazioni
Scheda Tecnica (TDS) · PA6 B2XLZ0
| Proprietà | Metodo di prova | Condizioni di prova | Valore tipico |
|---|---|---|---|
| Densità | ISO 1183 | 23°C | 1.08 g/cm3 |
| Resistenza alla trazione | ISO 527 | 50 mm/min | 30 MPa |
| Allungamento a rottura | ISO 527 | 50 mm/min | 350% |
| Resistenza alla flessione | ISO 178 | 2 mm/min | 25 MPa |
| Modulo di flessione | ISO 178 | 2 mm/min | 600 MPa |
| Resistenza all’urto Charpy con intaglio | ISO 179 | 23°C | 100 kJ/m2 |
| Temperatura di deflessione termica (HDT) · 0.45 MPa | ISO 75 | non ricotto | 105°C |
| Valutazione della fiamma | UL 94 | 1.6 / 2.0 / 3.2 mm | HB |
I valori tipici e gli intervalli prestazionali servono alla selezione del grado. Le formulazioni su misura possono essere adattate ai requisiti applicativi. Le proprietà finali fanno riferimento al TDS del grado scelto e non costituiscono garanzie di specifica.
- Questa tabella riguarda solo B2XLZ0. Per altri gradi consultate la rispettiva TDS.
- I valori tipici delle schede dei gradi indicati servono alla selezione; non sono proprietà universali né garanzie di fornitura. Confermate colore, provino e condizioni di prova del grado offerto.
Condizioni di elaborazione · B2XLZ0
80–90°C
2–4 h
220–230°C
80–100°C
Stoccaggio e movimentazione
PA6 è altamente igroscopico. Conservare sigillato in un ambiente asciutto. Utilizzare all'interno del nostro 24 h dopo l'apertura o la riasciugatura.
Prodotti correlati
Suzhou Jinsu New Material Co., Ltd.
WhatsApp: +86 17351132569
sales@maxnmtech.com
Applicazioni in dettaglio
Imballaggi in coestrusione multistrato
B2XLZ0 is typically run in a five-layer structure such as PE structural layer / tie layer / toughened PA6 / tie layer / PE sealing layer. The toughened layer delivers barrier and impact resistance, the PE layers handle heat sealing and cost, and the tie layers bond nylon to polyolefin. Hold melt temperature at 220–230°C and keep inter-layer temperature differences under 30°C, or the parison develops interface instability and delamination.
Contenitori alimentari e farmaceutici soffiati
Melt strength decides the blow-molding window: B2XLZ0 runs at about 2 g/10min MFI (235°C/2.16kg), so sag is low and large-diameter, high-neck-ratio bottles and jerry cans are practical. Mold temperature of 80–100°C improves surface gloss and dimensional stability; vent the mold properly or the inner wall develops pitting. For food contact, specify food-grade colorants and additives and supply compliance statements under the target market's rules, such as EU 10/2011 or FDA 21 CFR.
Film, fogli estrusi e riempimento a caldo
Beyond hollow blow molding, B2XLZ0 also suits cast film, thermoforming sheet and hot-fill packaging. HDT is 105°C at 0.45 MPa, so 85–95°C hot fill and pasteurisation cycles are tolerable; on the cold side the 350% elongation keeps containers from cracking in frozen storage and cold-chain transport. Dry to below 0.1% moisture before extrusion or the film shows bubbles and silver streaks.
Domande frequenti
Il PA6 tenacizzato può essere usato a contatto con alimenti?
Yes, with a food-grade formulation. B2XLZ0 natural base resin carries no restricted additives, but confirm the colorant, antioxidant and release agent are food-grade for the actual shipment, and supply compliance statements for the target market (EU 10/2011, FDA 21 CFR, and so on). Pharmaceutical packaging also needs extractables and leachables assessment.
A cosa fare attenzione nella coestrusione soffiata multistrato?
Three things matter most: interlayer adhesion, which needs a matched tie-layer resin or the container delaminates on impact; closely matched melt temperatures across layers, held within 30°C to avoid interface disturbance; and drying, with PA6 moisture below 0.1% or bubbles and silver streaks appear. Use an adjustable die to fine-tune parison wall distribution.
In che cosa B2XLZ0 differisce dal PA6 standard?
Standard PA6 is stronger and stiffer but elongates only tens of percent and cracks easily under low-temperature or high-rate impact. B2XLZ0 trades some stiffness and strength (600 MPa modulus, 30 MPa tensile) for 100 kJ/m² notched impact and 350% elongation, which suits packaging and containers that must absorb impact energy.