Quay lại danh mục

PA6 tăng độ dai

PA / Nylon

PA6 t?ng ?? dai B2XLZ0 v?i va ??p có khía 100 kJ/m² và ?? gi?n dài 350%, dành cho ??ng ??n nhi?u l?p và bình ch?a th?c ph?m, d??c ph?m th?i. Yêu c?u TDS, m?u và báo giá.

Mẫu miễn phí: 5–10 kg. Đơn hàng thử: tối thiểu 25 kg. Sản xuất thường xuyên: tối thiểu 1.000 kg. Khách hàng thanh toán chi phí vận chuyển.

Jinsu chưa hoàn tất chứng nhận UL Yellow Card. Dữ liệu TDS và kết quả thử nghiệm UL94 không đồng nghĩa với việc được UL công nhận. Nếu dự án yêu cầu Yellow Card, hãy xác minh chứng nhận của đúng mã vật liệu trước khi phê duyệt hoặc mua hàng.

Thông số kỹ thuật

  • •B2XLZ0 · PA6 tăng dai
  • •100 kJ/m² va đập có khía · ISO 179
  • •Độ giãn dài 350% · Đồng đùn nhiều lớp và thổi

Ứng dụng

Bao bì đồng đùn nhiều lớpBình chứa thực phẩm thổiBình chứa dược phẩm thổiMàng và tấm đùnChiết rót nóng và chuỗi lạnh

Bảng dữ liệu kỹ thuật (TDS) · PA6 B2XLZ0

Tài sảnPhương pháp thử nghiệmĐiều kiện thử nghiệmGiá trị điển hình
Mật độISO 118323°C1.08 g/cm3
Độ bền kéoISO 52750 mm/min30 MPa
Độ giãn dài khi đứtISO 52750 mm/min350%
Độ bền uốnISO 1782 mm/min25 MPa
Mô đun uốnISO 1782 mm/min600 MPa
Độ bền va đập Charpy có khíaISO 17923°C100 kJ/m2
Nhiệt độ lệch nhiệt (HDT) · 0,45 MPaISO 75chưa ủ nhiệt105°C
Đánh giá ngăn lửaUL 941.6 / 2.0 / 3.2 mmHB

Các giá trị điển hình và khoảng tính năng dùng để tham khảo khi chọn mã vật liệu. Công thức tùy chỉnh có thể được điều chỉnh theo yêu cầu ứng dụng. Tính năng cuối cùng theo TDS của mã vật liệu đã chọn và không phải là thông số được bảo đảm.

  • Bảng này chỉ áp dụng cho B2XLZ0. Với mã khác, vui lòng xem TDS riêng.
  • Giá trị tiêu biểu từ bảng dữ liệu của mã nêu trên chỉ dùng để chọn vật liệu, không phải thuộc tính chung hay bảo đảm mua hàng. Hãy xác nhận màu, mẫu thử và điều kiện thử của mã được cung cấp.

Điều kiện xử lý · B2XLZ0

Nhiệt độ sấy

80–90°C

Thời gian khô

2–4 h

Nhiệt độ nhựa nóng chảy

220–230°C

Nhiệt độ khuôn

80–100°C

Lưu trữ & Xử lý

PA6 có tính hút ẩm cao. Bảo quản kín trong môi trường khô ráo. Sử dụng trong vòng 24 giờ sau khi mở hoặc phơi khô lại.

Suzhou Jinsu New Material Co., Ltd.

WhatsApp: +86 17351132569

sales@maxnmtech.com

Ứng dụng chi tiết

Bao bì đồng đùn nhiều lớp

B2XLZ0 is typically run in a five-layer structure such as PE structural layer / tie layer / toughened PA6 / tie layer / PE sealing layer. The toughened layer delivers barrier and impact resistance, the PE layers handle heat sealing and cost, and the tie layers bond nylon to polyolefin. Hold melt temperature at 220–230°C and keep inter-layer temperature differences under 30°C, or the parison develops interface instability and delamination.

Bình chứa thực phẩm và dược phẩm thổi

Melt strength decides the blow-molding window: B2XLZ0 runs at about 2 g/10min MFI (235°C/2.16kg), so sag is low and large-diameter, high-neck-ratio bottles and jerry cans are practical. Mold temperature of 80–100°C improves surface gloss and dimensional stability; vent the mold properly or the inner wall develops pitting. For food contact, specify food-grade colorants and additives and supply compliance statements under the target market's rules, such as EU 10/2011 or FDA 21 CFR.

Màng, tấm đùn và chiết rót nóng

Beyond hollow blow molding, B2XLZ0 also suits cast film, thermoforming sheet and hot-fill packaging. HDT is 105°C at 0.45 MPa, so 85–95°C hot fill and pasteurisation cycles are tolerable; on the cold side the 350% elongation keeps containers from cracking in frozen storage and cold-chain transport. Dry to below 0.1% moisture before extrusion or the film shows bubbles and silver streaks.

Câu hỏi thường gặp

PA6 tăng dai có dùng được cho tiếp xúc thực phẩm không?

Yes, with a food-grade formulation. B2XLZ0 natural base resin carries no restricted additives, but confirm the colorant, antioxidant and release agent are food-grade for the actual shipment, and supply compliance statements for the target market (EU 10/2011, FDA 21 CFR, and so on). Pharmaceutical packaging also needs extractables and leachables assessment.

Đồng đùn thổi nhiều lớp cần lưu ý gì?

Three things matter most: interlayer adhesion, which needs a matched tie-layer resin or the container delaminates on impact; closely matched melt temperatures across layers, held within 30°C to avoid interface disturbance; and drying, with PA6 moisture below 0.1% or bubbles and silver streaks appear. Use an adjustable die to fine-tune parison wall distribution.

B2XLZ0 khác PA6 tiêu chuẩn ở điểm nào?

Standard PA6 is stronger and stiffer but elongates only tens of percent and cracks easily under low-temperature or high-rate impact. B2XLZ0 trades some stiffness and strength (600 MPa modulus, 30 MPa tensile) for 100 kJ/m² notched impact and 350% elongation, which suits packaging and containers that must absorb impact energy.